|
The results show that given model and calculation method are accurate and less computational effort ,and can be made the overall process analysis of conical parts and be applied to process analysis of other axisymmetrical stampings.
|
|
|
结果表明，所建模型和计算方法准确可靠，计算量少，可进行完整的过程解析，并可应用于其它轴对称冲压件过程解析。 |
|
The results show that high-temperature calcinations, Alkaline Leaching and stirring scrubbing can't separate the current collectors and active materials effectively.
|
|
|
研究结果表明焙烧法、碱浸法和搅拌擦洗法都不能达到活性物质与集流体的有效分离。 |
|
The results show that ignoring change of friction heat flow intensity will bring large deviation to temperature field simulation.
|
|
|
结果表明：如果忽略制动过程中摩擦热流强度的变化，会给温度场模拟带来较大的偏差。 |
|
The results show that improving the rolling velocity and reducing the galvanizing time will result in reduction of strength loss after galvanizing, and increase of bend torsion valve, thus productivity is improved.
|
|
|
结果表明：提高收线速度，减少浸锌时间，镀后强度损失减小，弯扭值提高，生产效率提高。 |
|
The results show that in 185℃ saturated steam, pyrite tailing doesn't hydrate alone, but is converted into calcium silicate hydrate when mixed with lime.
|
|
|
结果表明：185℃饱和蒸汽压下，硫铁尾矿不具有水热水化的能力，硫铁尾矿与石灰可以形成具有胶凝性能的水化产物。 |
|
The results show that in determining the maximum multiplier effect of a certain branch area we should take a series of measures to improve the MPC of each branch, the investment in-flow rate of the certain branch area, the investment out-flow rate of the
|
|
|
结果表明：当投资对特定子区域的乘数效果成为关注的目标时，应当采取措施提高各子区域的边际消费倾向、特定子区域的投资内流比、非特定子区域的投资外流比、期初投资流入特定子区比例，以获得投资对特定子区域乘数效果的最佳化目标。 |
|
The results show that in the case of no wind the oil film moves southwestward along with the tidal Current, its area increases and thickness decreases, and the port is not polluted during ebb tide; a part of the oil film is blocked by the northern jetty,
|
|
|
计算结果表明，在静风情况下，落潮期间油膜随落潮流向西南方向漂移，面积扩大，厚度减小，港区未受油污的影响；涨潮期间油膜受北导堤的阻挡，部分油污留在港区。 |
|
The results show that in the later stage of the nucleation process, ① The maximum slip velocity is monotonically accelerating; ② The slipping hot spot (where the slip rate is maximum) migrates spontaneously from a certain instant, and such migration is sp
|
|
|
结果表明，在成核的后期阶段：①最大位移速率单调加速增加；②滑动热点（最大滑动速率处）在后期阶段开始自发性迁移，且在空间上连续；③当最大滑动速率达到可以明显探测的量级时（高于载入速率一个数量级以上），倒计时间为20小时或更长一些，这时的速率变化可作为临震预测标志；④平均滑动速率与倒计时间的关系在临震阶段呈对数线性趋势，由此可推测微震活动增长率与倒计时间同样存在对数线性关系；⑤正应力的变化对上述时间尺度有延长作用，使之大致增加到原数值的2倍。 |
|
The results show that increase of flow Reynolds number and decrease of sensitivity of turbine performance to Reynolds number are two key technologies to aerodynamic design of high performance LPT.
|
|
|
设计结果表明提高涡轮工作雷诺数和降低涡轮性能对雷诺数变化的敏感程度是低雷诺数环境下高性能涡轮气动设计的关键。 |
|
The results show that induction remelting technique is satisfied to use free - spraying alloy powder.
|
|
|
随感应电流的增大，熔化时间缩短，而组织状态未发生明显的变化。 |
|
The results show that it's an effective way to improve the efficiency and reduce the operating cost to introduce intelligent control into biological treatment of wastewater, the application of intelligent control is broad and in-depth abroad and is at ear
|
|
|
结果表明，在污水生物处理中引人智能控制是一种提高处理效率、降低运行成本的有效方法，国内在污水生物处理智慧控制的应用研究与国外有较大的差距，国内的研究及应用还处在发展阶段，应当加强。 |
