|
The mean thickness of the tuberculum sellae was . mm,and that of the planum sphenoidale was 0.7 mm.
|
|
|
鞍结节骨质的平均厚度为. mm,蝶骨平台的骨质厚度为0.7 mm。 |
|
The mean transverse and anterior posterior diameters of sciatic nerve at the levels of ischial tuberosity, middle one third and lower one third of the thigh were .mm, . mm, .mm and 0.9mm, 0.89mm, 0.88mm respoectively.
|
|
|
在坐骨结节、大腿中／ 及下／ 平面的横径及前后径分别为．mm、． mm、．mm及0．9mm、0．89mm、0．88mm； |
|
The means and approaches to develop real-time road traffic routing arrangement system are illustrated by using CBR, and road system prototype at Hampton in Virginia is quoted.
|
|
|
引用Virginia的hampton路径系统原型,说明了开发实时道路交通行程安排系统的方法与步骤。 |
|
The measurement of EMG and deglutition pressure after glossal reconstruction
|
|
|
舌再造术后舌部肌电及吞咽压的测定 |
|
The measurement of baumann's angle to predict the complicated cubitus varus in supracondylar fracture of the humerus
|
|
|
Baumann角测量预测肱骨髁上骨折肘内翻的研究 |
|
The measurement of fast neutron absorbed dose by CaSO_ (Tm)-glucose method
|
|
|
测量快中子吸收剂量的CaSO_(Tm)-葡萄糖法 |
|
The measures for improving wear of camber for lockup were proposed.
|
|
|
针对锁紧弧面的磨损提出了改善措施。 |
|
The measuring precision of spring plenum length is up to ±0.97mm with 9% confidence by applying new method.
|
|
|
采用新方法检测弹簧空腔长度,并增加了多定标测量道数,使弹簧空腔长度的检测精度为±0.97mm,置信概率为9%。 |
|
The mechanical and flame retardant properties of material would be the best when the DCP is .0g,and the monomer MMA and MAH are 0ml and g:The extension strength is .7MPa; rapture elongation is .8%; impact strength is 0.8 kJ/m~;
|
|
|
在原位增容反应中,当DCP用量为.0 g、单体MMA为0 mL、MAH为 g时原位反应制得材料的性能最佳:拉伸强度为.7 MPa、断裂伸长率为 .8%、冲击强度为0.8 kJ/m、垂直燃烧等级达到UL9V-0级. |
|
The mechanical performance of aluminum alloy(0 )was investigated with its plate tension,notched plate tension and pure shear.
|
|
|
通过对铝合金(0 )进行平板拉伸试验、带缺口的平板拉伸试验及纯剪切试验,研究了铝合金在三种应力下的力学性能. |
|
The mechanical properties of -0v. -% mullite(w)/TZP. compo-sites at room temperature areσ_f=00MPa and K_(IC)=Mpa ~(/m)which are closely same asTZP matrix;
|
|
|
mullite(W)含量在-0 V.-%时,室温力学性能与基质 TZP 大致相同:σ_f=00MPa,K_(IC)=MPa~(/m); |
