|
The results show that factors affecting the pore diameter of porous materials are the sintering temperature and time, the added quantity of pore former and the granularity of glass powder etc.
|
|
|
研究结果表明：烧结温度和时间、造孔剂的用量及玻璃粉体的粒度等都将影响多孔材料的孔径。 |
|
The results show that for organic solvent typed fluorocarbon lacquer and specially treated water soluable fluorocarbon lacquer, the content of fluorocarbon resin can be determined accurately with the above method.
|
|
|
结果表明，采用氧弹燃烧法配合氟离子电极对有机溶剂型氟碳漆及处理后水溶性氟碳漆的氟碳树脂含量能够进行准确测定。 |
|
The results show that geological radar is an effective method in the investigation of karst collapse.
|
|
|
结果表明，地质雷达在岩溶塌陷调查中应用效果较好。 |
|
The results show that given model and calculation method are accurate and less computational effort ,and can be made the overall process analysis of conical parts and be applied to process analysis of other axisymmetrical stampings.
|
|
|
结果表明，所建模型和计算方法准确可靠，计算量少，可进行完整的过程解析，并可应用于其它轴对称冲压件过程解析。 |
|
The results show that high-temperature calcinations, Alkaline Leaching and stirring scrubbing can't separate the current collectors and active materials effectively.
|
|
|
研究结果表明焙烧法、碱浸法和搅拌擦洗法都不能达到活性物质与集流体的有效分离。 |
|
The results show that ignoring change of friction heat flow intensity will bring large deviation to temperature field simulation.
|
|
|
结果表明：如果忽略制动过程中摩擦热流强度的变化，会给温度场模拟带来较大的偏差。 |
|
The results show that improving the rolling velocity and reducing the galvanizing time will result in reduction of strength loss after galvanizing, and increase of bend torsion valve, thus productivity is improved.
|
|
|
结果表明：提高收线速度，减少浸锌时间，镀后强度损失减小，弯扭值提高，生产效率提高。 |
|
The results show that in 185℃ saturated steam, pyrite tailing doesn't hydrate alone, but is converted into calcium silicate hydrate when mixed with lime.
|
|
|
结果表明：185℃饱和蒸汽压下，硫铁尾矿不具有水热水化的能力，硫铁尾矿与石灰可以形成具有胶凝性能的水化产物。 |
|
The results show that in determining the maximum multiplier effect of a certain branch area we should take a series of measures to improve the MPC of each branch, the investment in-flow rate of the certain branch area, the investment out-flow rate of the
|
|
|
结果表明：当投资对特定子区域的乘数效果成为关注的目标时，应当采取措施提高各子区域的边际消费倾向、特定子区域的投资内流比、非特定子区域的投资外流比、期初投资流入特定子区比例，以获得投资对特定子区域乘数效果的最佳化目标。 |
|
The results show that in the case of no wind the oil film moves southwestward along with the tidal Current, its area increases and thickness decreases, and the port is not polluted during ebb tide; a part of the oil film is blocked by the northern jetty,
|
|
|
计算结果表明，在静风情况下，落潮期间油膜随落潮流向西南方向漂移，面积扩大，厚度减小，港区未受油污的影响；涨潮期间油膜受北导堤的阻挡，部分油污留在港区。 |
|
The results show that in the later stage of the nucleation process, ① The maximum slip velocity is monotonically accelerating; ② The slipping hot spot (where the slip rate is maximum) migrates spontaneously from a certain instant, and such migration is sp
|
|
|
结果表明，在成核的后期阶段：①最大位移速率单调加速增加；②滑动热点（最大滑动速率处）在后期阶段开始自发性迁移，且在空间上连续；③当最大滑动速率达到可以明显探测的量级时（高于载入速率一个数量级以上），倒计时间为20小时或更长一些，这时的速率变化可作为临震预测标志；④平均滑动速率与倒计时间的关系在临震阶段呈对数线性趋势，由此可推测微震活动增长率与倒计时间同样存在对数线性关系；⑤正应力的变化对上述时间尺度有延长作用，使之大致增加到原数值的2倍。 |
