|
with high pressure syringe, dosage 80-00ml, injection rate .-.0ml/s, scanning delay time - 0s, scanning total time 0-70s. |
中文意思: 使用高压注射器,注入对比剂优维显速度为 .- ml/s,剂量为80-00 ml,延迟时间为- 0 s,扫描时间0-70 s。 |
以下为相关句子列表(点击查看,可以看对应的解释):
|
|
white lipped deers,8 red deers and sikas were used to study the isozyme spectra of serum amylase by means of a polyacrylamide gel electrophoresis.
|
|
|
采用聚丙烯酰胺凝胶电泳法对 头白唇鹿,8头马鹿和头梅花鹿的血清淀粉酶同工酶进行了比较研究。 |
|
wholly advance teaching methods;
|
|
|
整体优化教学方法; |
|
wiping out cockroach's disgrace
|
|
|
为蟑螂洗刷污名(续)——保护生物多样性 |
|
wiping out cockroach's disgrace
|
|
|
为蟑螂洗刷污名——保护生物多样性 |
|
with a gradient eluting system of 0.0 mol/LKH PO -H PO (pH .7)-methanol.
|
|
|
流动相A液为0.0mol/LKHPOH PO缓冲液(pH.7),流动相B液为甲醇; 梯度洗脱; |
|
with high pressure syringe, dosage 80-00ml, injection rate .-.0ml/s, scanning delay time - 0s, scanning total time 0-70s.
|
|
|
使用高压注射器,注入对比剂优维显速度为 .- ml/s,剂量为80-00 ml,延迟时间为- 0 s,扫描时间0-70 s。 |
|
with increasing the ratio value D/D0 of equivalent diameter of the sparger to oxidation tank , the OR increases, but when the D/D0 is larger than (0.8), the increase of the OR is slow down;
|
|
|
曝气器与氧化槽当量直径比值D/D0增加时,氧化速率增加; 但当D/D0大于0.8时,氧化速率变化较小。 |
|
with the mixed solution of EDTA and H_ cit as the eluant, the kinetic of the chromatographic precess is better than that with EDTA eluant and becomes better and better with the increase of the concentration of H_ cit;
|
|
|
采用EDTA+H_ cit混合洗提剂时,动力学性能比单独用EDTA时有所改善,而且随着H_ cit浓度的增加,色谱动力学性能也表现得越来越好; |
|
xylose (8. mg/L), mannose (.0 mg/L), glucose (. mg/L), galactose (.80 mg/L), rhamnose (. mg/L), ribose (. mg/L), and fucose (. mg/L) were found in the sample. The GC method was also the most precise of the three methods.
|
|
|
气相色谱法测得的生活污水中各种单糖,如木糖、甘露糖、葡萄糖、半乳糖、鼠李糖、核糖、岩藻糖的质量浓度分别为8.、.0、.、.80、.、.、.mg/L。 |
|
y=-.9 +9.99x+.x .This equation apply to calculate the sella turcica of adult.
|
|
|
y=-.9+9.99x_+.x_.可供推算成人蝶鞍侧位面积使用. |
|
zygomaticus minimus and m. risorius is .±.mm, .±.8mm and 0.±.mm respectively. The angle between the m.
|
|
|
颧大肌、颧小肌、笑肌长依次为 .± .mm、 .± .8mm、 0 .± .mm ; |
|
|
|